DIY Tub Installation.
DIY Tub Installation.
Blog Article
Presented here below you will discover additional first-rate help and advice relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Setting up a tub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a reasonably tough task. If the old bathtub is easily available, the project can relocate immediately; if you have to open a wall surface to get rid of the old tub and place the new bathtub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will require an assistant to move out the old bathtub and also set in the brand-new one. Ensure you have certified on your own for the job and also fit attempting it. As opposed to employing a contractor to take control of a halfway-completed job, it is better to take into consideration employing one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This article will certainly aid you mount a new bath tub in your shower room if you have already bought a new bathtub and also don't require to change the setup of your previous supply of water pipes.
Your devices and material list must comprise the following:
Planning for the Installation
First of all, the sustaining frame provided with the bath needs to be fitted (if required) according to the maker's guidelines. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to stop strain on the tub.
Fit the versatile faucet adapters to the bottom of the two taps utilizing 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your setup, then the first thing you must do is separate the water. After doing so, turn on the faucets to drain pipes any water remaining in the system. The process of removing the existing faucets can be fairly problematic due to the limited accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a fabric all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to carrying on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing the two wooden boards under its feet, position the bath tub in the called for position. The wood boards are practical in uniformly spreading the weight of the tub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bath tub till the level checks out level.
To install taps, fit all-time low of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the other faucet.
Activate the water system as well as inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub and additionally examine the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, fix the bathroom paneling as explained in the producer's user's manual. Tiling and also sealing around the bathtub needs to wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a link to the current supply pipes.
If you require to fit a monobloc, then you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location between the faucet and the sink. Protect the tap in position with the manufacturer supplied backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, causing the water to penetrate the wall surface in between the bathroom and also the tiling, leading to problems with wetness and possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your components and also installations. They are sold in tubes and cartridges, as well as are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our section on How to Install a Bathtub. Thank you so much for finding the time to read through our blog post. Loved our article? Please share it. Let another person discover it. Many thanks for your time. Come back soon.
Click Here Report this page